OldTools Archive
Recent | Bios | FAQ |
109145 | scott grandstaff <scottg@s...> | 2002‑08‑27 | Re: Rivets in perfect handle screwdrivers |
Tom..... what are you doing Tom?? Perfect handles, indeed! I'm going to go after hand cranked grinders now, haaaaarumph. Kidding, kidding There's room for many and more. But.. if you find one less than 3" long..................... OK, I just use soft steel rod. Any auto parts or many hardware stores. Look right next to the allthread rack. While you're there might as well get some brass brazing rod. Some of the woods look really cool with the brass rivets instead of steel. You can also use knifemakers 2 piece rivets. I get mine from Atlantacutlery(.com). They aren't really the best for screwdrivers though since they are really made for a flat handles and screwdriver handles ain't. You have to counterbore them in to sit flush at the least. You're right that they aren't headed over like most rivets. You want to slightly taper ream the holes. If you countersink you'll have to pein forever to fill it and a slight taper works plenty good. I have an old drill bit I tapered by hand just for this job. Only took a minute. I know it's old news, but here's a copy of my old handle fitting post in case you or anyone wants to see it and can't find it in the archives. Perfect Handle almost Perfect Hello Galoots, I received some favorable comments on my perfect handle scratchawl and thought I'd share how the handle slab "inlays" were made. After all, it is not very hard to find good screwdrivers or wrenches with damaged handles. And they're great tools to use when in good shape. It's pretty easy to fit those oval, curving inlayed scales (knife maker's term), believe it or not. All of the smaller sizes were made to take 1/4" stock. The larger (over 8" or so) take 3/8" stock. Pick an adequate supply of your favorite wood. The first thing you do is lay your frame down on the stock and trace around it giving you a rough outline. Do this twice of course, once for each scale. Next, saw the blanks out making sure not to get anywhere near the layout lines you just made. You want some slop all around. Now you should have 2 oversize blanks. Here comes the first "trick". Lay your blanks on each side of the frame where they'll go. Pick the sandwich up and place the whole magilla in-between the jaws of a heavy bench vice. You will probably have to wiggle a bit under very light tension to make sure everything lines up. You want a bit of overhang all around. When you're satisfied, turn the crank. And again. Really reel on it. Heave. Smash the wood into the frame. If you've chosen a very hard wood it probably won't seat all the way down in the frame no matter how hard you pull. In this case, before you release the tension, mark the frame and handles so you can put them back on the same side. They are not always identical. Remove the tool from the vice. No matter how hard the wood, the frame shape will have dented it bigtime from the pressing. Rasp the scales closer to this dent, but not all the way to it. Now replace it in the vice and press again. This time they should seat all the way down. Here comes trick 2. There are 2 rivet holes in your frame from where the handles were attached in the first place. Remove one of your new scales. Pick a drill bit the same size as the rivets you will use that still will pass through the frame holes. I use brass brazing rod from the auto parts or welder's supply. It comes in several sizes and its dirt cheap. With one handle removed, drill down through the frame holes through one handle. Replace the second scale and drill back through the hole you just made through the second one. Now everything will line up just dandy. I usually scrape the old frame clean where the handles live and place a dollop of 5 minute epoxy on each side. For your first one you might want to go with slower setting glue. Reassemble (pay attention to your marks). The old rule for rivets is twice the diameter sticking out of the work. You can get by with less for this, maybe 1/16 inch on each side. I just push the rod through and cut off what I need with a hacksaw. Lay it on your anvil or other unyielding surface and peen. In case you never did this part before, here's how it goes. If you just pound straight down on the rivets they'll eventually bend and ruin your work. What you want to do is hit the top, outside edges of the rivets alternating around the diameter. After several blows turn over and do the other side. Keep switching sides until the rivets draw all the way down with the handles pressed tight to the frame and glue squeezing out. Now you can rasp, file, scrape, sand to hand fitting oval perfection. All this seemed long to write and probably long to read too, but really, once you have done one or two it's pretty fast. For my regular screwdriver set (7 sizes) I used hard maple and black walnut on every-other size. Looks pretty nice hanging up on the rack. I don't think I originally paid over 50 cents for any of them. yours, Scott ******************************* Scott Grandstaff Box 409 Happy Camp, Ca 96039 scottg@s... http://www.snowcrest.net/kitty/hpages/index.html |
|||
109131 | Tom Thornton <tomthornton@n...> | 2002‑08‑27 | Rivets in perfect handle screwdrivers |
Been slowly collecting perfect handle screwdrivers. ( steel shaft top to bottom, fattened at top with two pieces of wood forming handle, piece on each side of the flat handle) Wood handles can be present or not. They take a bit of time to derust and restore and require minimum storage/display area,(which is now at premium ) Is fun to make replacement handles but attaching them is a trick. I note the originals have a heavy steel rivets ( shaft, not hollow) with neat ( not overstruck ) head on both sides. The length depends on the width of the wooden handles. I'm at a loss as to where to go to try and find replacement. Only rivets I know are short ( under 1/2 inch ) and with big heads. Anyone any idea where and/or what I could use, round shaft, anywhere from 3/4 to 1 inch long, about 3/16 in diameter, soft enf to form top without beating to death. -- Tom Thornton Cincinnati #3, F&AM , Morristown, N.J., USA Collector of old tools, specializing in hand cranked grindstones |
|||
109150 | Kilpatrick Jay Capt HQ AFMC/DRO <Edwin.Kilpatrick@w...> | 2002‑08‑27 | RE: Rivets in perfect handle screwdrivers |
I'm no metal smith, but if you annealed pieces of steel rod from the local hardware store, would that work? All these SOYBIPM types seem to peen this stuff (Brass and Steel) then file it off. I don't see how that process is any different than what you want to do. BTW, I was practicing dovetails last night and learned a few things: 1. This was my third attempt and I still suck...not the gloatable kind either. 2. I'm getting marginally better (my only consulation) 3. A real bench would help (I think) 4. Books aren't enough for me, so I'm ordering Kingshot and/or Cosman video(s) unless someone in the Dayton area would let me borrow their copy(ies) _Jay Kilpatrick Tom Thornton wrote: Anyone any idea where and/or what I could use, round shaft, anywhere from 3/4 to 1 inch long, about 3/16 in diameter, soft enf to form top without beating to death. |
|||
109138 | Scott Quesnelle <scottq@c...> | 2002‑08‑27 | Re: Rivets in perfect handle screwdrivers |
> > Anyone any idea where and/or what I could use, round shaft, > anywhere from 3/4 to 1 inch long, about 3/16 in diameter, soft enf > to form top without beating to death. Since you are in the U.S. I would suggest you try RJ Leahy at http://www.rjleahy.com/Store/rivets/trvr.htm in Canada I would go with Spaenaur For $3.70 you can get a 1 lb box of 3/16" diameter rivets. I would suggest you get ones longer than you think you really need, then trim them so that the amount sticking out past the hole is the diameter of the rivet. To keep the original round head nice, grab a piece of scrap wood, or steel and drill a half round in it with a drill bit about 1.5 times larger than the head, this will help it from moving around on you and keep the head nice looking, as for making the peened end nice, lots of little nice taps with a ballpeen (or engineer's hammer). For final touch ups, you can make another depression in the end of a steel bar, and use this as the final setter on the rivet. Hope that helps, Scott Quesnelle Galoot in Training > > > -- > > Tom Thornton > Cincinnati #3, F&AM , Morristown, N.J., USA > Collector of old tools, specializing in hand cranked grindstones > > > > Archive: http://www.frontier.iarc.uaf.edu/~cswingle/archive > To unsubscribe or change options, use the web interface: > http://galoots.law.cornell.edu/cgi-bin/lyris.pl?enter=oldtools > |
|||
109149 | "Michael Lietzow" <mlietzow@s...> | 2002‑08‑27 | Re: Rivets in perfect handle screwdrivers |
Hi Tom and all, I was just fixing to post a question or two about this topic when I read this message so I thought I'd just jump on here. I can't answer your riveting question but I'd like to find out more about this type of screwdriver. I'd never seen this type until last Saturday when I picked up three of them at a local flea market. They all share a similar design but were made by different manufacturers (I think). The neatest one has a very interesting marking around a round steel shaft. It's in a spiral pattern (sort of like the stripe on a barbers pole) and says "PERFECT HANDLE, ?????sville, Conn" and maybe some other info. The second one is much newer, was made by Irwin, has a squared shaft (though not a true square) and looks a lot like the super beefy one shown here: http://www.goantiques.com/texis,smith_perfect_handle,3d16032d28.html The third one has no markings that I can find but has a round shaft like the one marked Perfect Handle. I'd appreciate any info on this type of screwdriver. What are they designed for? They seem to be way too sturdy for simply turning screws, especially the Irwin one. Also, is "Perfect Handle" a brand name or simply a style of handle. TIA for any information. Cheers, Mike |
|||
109134 | paul womack <pwomack@e...> | 2002‑08‑27 | Re: Rivets in perfect handle screwdrivers |
Tom Thornton wrote: > > Anyone any idea where and/or what I could use, round shaft, > anywhere from 3/4 to 1 inch long, about 3/16 in diameter, soft enf > to form top without beating to death. Check with the knife making fora. They do this kind of handle riveting all the time, and presumably have answers for you. BugBear |
|||
109211 | "Steve Reynolds" <stephenereynolds@e...> | 2002‑08‑28 | Re: Rivets in perfect handle screwdrivers |
Michael asked: [snip] > The neatest one has a > very interesting marking around a round steel shaft. It's in a spiral > pattern (sort of like the stripe on a barbers pole) and says "PERFECT > HANDLE, ?????sville, Conn" and maybe some other info. [snip] >What are they designed for? They seem to be way too sturdy > for simply turning screws, especially the Irwin one. Also, is "Perfect > Handle" a brand name or simply a style of handle. Perfect Handle was the trademark of HD Smith & Co. who hung out their shingle in Plantsville, Connecticut: http://www.mjdtools.com/books/22563.htm As for the Irwin, whaddya mean TOO sturdy? Comemon, dagnabit, ain't no such thing. Those boys were made to sit in the head of the biggest, rustiest, nastiest screws and have a wrench put on the shank for extra torque. Ain't no too sturdy about it. Especially if you're one to abuse a screwdrive and use it to lever up a Model T Ford to retrieve the coffee money you dropped underneath. Big ol' shank will survive that while your chiwanese one will twist like a pretzel. Regards, Steve |
|||
Recent | Bios | FAQ |